Tag Archives: roller chain sizes

China wholesaler ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes

Product Description


ROLLER CHAIN

Roller chain or bush roller chain is the type of chain drive most commonly used for transmission of mechanical power on many kinds of domestic, industrial and agricultural machinery, including conveyors, wire- and tube-drawing machines, printing presses, cars, motorcycles, and bicycles. It consists of a series of short cylindrical rollers held together by side links. It is driven by a toothed wheel called a sprocket. It is a simple, reliable, and efficient means of power transmission.

LUBRICATION

Many driving chains (for example, in factory equipment, or driving a camshaft inside an internal combustion engine) operate in clean environments, and thus the wearing surfaces (that is, the pins and bushings) are safe from precipitation and airborne grit, many even in a sealed environment such as an oil bath. Some roller chains are designed to have o-rings built into the space between the outside link plate and the inside roller link plates. Chain manufacturers began to include this feature in 1971 after the application was invented by Joseph Montano while working for Whitney Chain of Hartford, Connecticut. O-rings were included as a way to improve lubrication to the links of power transmission chains, a service that is vitally important to extending their working life. These rubber fixtures form a barrier that holds factory applied lubricating grease inside the pin and bushing wear areas. Further, the rubber o-rings prevent dirt and other contaminants from entering inside the chain linkages, where such particles would otherwise cause significant wear.[citation needed]

There are also many chains that have to operate in dirty conditions, and for size or operational reasons cannot be sealed. Examples include chains on farm equipment, bicycles, and chain saws. These chains will necessarily have relatively high rates of wear, particularly when the operators are prepared to accept more friction, less efficiency, more noise and more frequent replacement as they neglect lubrication and adjustment.

Many oil-based lubricants attract dirt and other particles, eventually forming an CHINAMFG paste that will compound wear on chains. This problem can be circumvented by use of a “dry” PTFE spray, which forms a solid film after application and repels both particles and moisture.

VARIANTS DESIGN

Layout of a roller chain: 1. Outer plate, 2. Inner plate, 3. Pin, 4. Bushing, 5. Roller
If the chain is not being used for a high wear application (for instance if it is just transmitting motion from a hand-operated lever to a control shaft on a machine, or a sliding door on an oven), then 1 of the simpler types of chain may still be used. Conversely, where extra strength but the smooth drive of a smaller pitch is required, the chain may be “siamesed”; instead of just 2 rows of plates on the outer sides of the chain, there may be 3 (“duplex”), 4 (“triplex”), or more rows of plates running parallel, with bushings and rollers between each adjacent pair, and the same number of rows of teeth running in parallel on the sprockets to match. Timing chains on automotive engines, for example, typically have multiple rows of plates called strands.

Roller chain is made in several sizes, the most common American National Standards Institute (ANSI) standards being 40, 50, 60, and 80. The first digit(s) indicate the pitch of the chain in eighths of an inch, with the last digit being 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. Thus, a chain with half-inch pitch would be a #40 while a #160 sprocket would have teeth spaced 2 inches apart, etc. Metric pitches are expressed in sixteenths of an inch; thus a metric #8 chain (08B-1) would be equivalent to an ANSI #40. Most roller chain is made from plain carbon or alloy steel, but stainless steel is used in food processing machinery or other places where lubrication is a problem, and nylon or brass are occasionally seen for the same reason.

Roller chain is ordinarily hooked up using a master link (also known as a connecting link), which typically has 1 pin held by a horseshoe clip rather than friction fit, allowing it to be inserted or removed with simple tools. Chain with a removable link or pin is also known as cottered chain, which allows the length of the chain to be adjusted. Half links (also known as offsets) are available and are used to increase the length of the chain by a single roller. Riveted roller chain has the master link (also known as a connecting link) “riveted” or mashed on the ends. These pins are made to be durable and are not removable.

USE

An example of 2 ‘ghost’ sprockets tensioning a triplex roller chain system
Roller chains are used in low- to mid-speed drives at around 600 to 800 feet per minute; however, at higher speeds, around 2,000 to 3,000 feet per minute, V-belts are normally used due to wear and noise issues.
A bicycle chain is a form of roller chain. Bicycle chains may have a master link, or may require a chain tool for removal and installation. A similar but larger and thus stronger chain is used on most motorcycles although it is sometimes replaced by either a toothed belt or a shaft drive, which offer lower noise level and fewer maintenance requirements.
The great majority of automobile engines use roller chains to drive the camshaft(s). Very high performance engines often use gear drive, and starting in the early 1960s toothed belts were used by some manufacturers.
Chains are also used in forklifts using hydraulic rams as a pulley to raise and lower the carriage; however, these chains are not considered roller chains, but are classified as lift or leaf chains.
Chainsaw cutting chains superficially resemble roller chains but are more closely related to leaf chains. They are driven by projecting drive links which also serve to locate the chain CHINAMFG the bar.

Sea Harrier FA.2 ZA195 front (cold) vector thrust nozzle – the nozzle is rotated by a chain drive from an air motor
A perhaps unusual use of a pair of motorcycle chains is in the Harrier Jump Jet, where a chain drive from an air motor is used to rotate the movable engine nozzles, allowing them to be pointed downwards for hovering flight, or to the rear for normal CHINAMFG flight, a system known as Thrust vectoring.

WEAR

 

The effect of wear on a roller chain is to increase the pitch (spacing of the links), causing the chain to grow longer. Note that this is due to wear at the pivoting pins and bushes, not from actual stretching of the metal (as does happen to some flexible steel components such as the hand-brake cable of a motor vehicle).

With modern chains it is unusual for a chain (other than that of a bicycle) to wear until it breaks, since a worn chain leads to the rapid onset of wear on the teeth of the sprockets, with ultimate failure being the loss of all the teeth on the sprocket. The sprockets (in particular the smaller of the two) suffer a grinding motion that puts a characteristic hook shape into the driven face of the teeth. (This effect is made worse by a chain improperly tensioned, but is unavoidable no matter what care is taken). The worn teeth (and chain) no longer provides smooth transmission of power and this may become evident from the noise, the vibration or (in car engines using a timing chain) the variation in ignition timing seen with a timing light. Both sprockets and chain should be replaced in these cases, since a new chain on worn sprockets will not last long. However, in less severe cases it may be possible to save the larger of the 2 sprockets, since it is always the smaller 1 that suffers the most wear. Only in very light-weight applications such as a bicycle, or in extreme cases of improper tension, will the chain normally jump off the sprockets.

The lengthening due to wear of a chain is calculated by the following formula:

M = the length of a number of links measured

S = the number of links measured

P = Pitch

In industry, it is usual to monitor the movement of the chain tensioner (whether manual or automatic) or the exact length of a drive chain (one rule of thumb is to replace a roller chain which has elongated 3% on an adjustable drive or 1.5% on a fixed-center drive). A simpler method, particularly suitable for the cycle or motorcycle user, is to attempt to pull the chain away from the larger of the 2 sprockets, whilst ensuring the chain is taut. Any significant movement (e.g. making it possible to see through a gap) probably indicates a chain worn up to and beyond the limit. Sprocket damage will result if the problem is ignored. Sprocket wear cancels this effect, and may mask chain wear.

CHAIN STRENGTH

The most common measure of roller chain’s strength is tensile strength. Tensile strength represents how much load a chain can withstand under a one-time load before breaking. Just as important as tensile strength is a chain’s fatigue strength. The critical factors in a chain’s fatigue strength is the quality of steel used to manufacture the chain, the heat treatment of the chain components, the quality of the pitch hole fabrication of the linkplates, and the type of shot plus the intensity of shot peen coverage on the linkplates. Other factors can include the thickness of the linkplates and the design (contour) of the linkplates. The rule of thumb for roller chain operating on a continuous drive is for the chain load to not exceed a mere 1/6 or 1/9 of the chain’s tensile strength, depending on the type of master links used (press-fit vs. slip-fit)[citation needed]. Roller chains operating on a continuous drive beyond these thresholds can and typically do fail prematurely via linkplate fatigue failure.

The standard minimum ultimate strength of the ANSI 29.1 steel chain is 12,500 x (pitch, in inches)2. X-ring and O-Ring chains greatly decrease wear by means of internal lubricants, increasing chain life. The internal lubrication is inserted by means of a vacuum when riveting the chain together.

CHAIN STHangZhouRDS

Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.

ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25

ASME/ANSI B29.1-2011 Roller Chain Standard Sizes
Size Pitch Maximum Roller Diameter Minimum Ultimate Tensile Strength Measuring Load
25 0.250 in (6.35 mm) 0.130 in (3.30 mm) 780 lb (350 kg) 18 lb (8.2 kg)
35 0.375 in (9.53 mm) 0.200 in (5.08 mm) 1,760 lb (800 kg) 18 lb (8.2 kg)
41 0.500 in (12.70 mm) 0.306 in (7.77 mm) 1,500 lb (680 kg) 18 lb (8.2 kg)
40 0.500 in (12.70 mm) 0.312 in (7.92 mm) 3,125 lb (1,417 kg) 31 lb (14 kg)
50 0.625 in (15.88 mm) 0.400 in (10.16 mm) 4,880 lb (2,210 kg) 49 lb (22 kg)
60 0.750 in (19.05 mm) 0.469 in (11.91 mm) 7,030 lb (3,190 kg) 70 lb (32 kg)
80 1.000 in (25.40 mm) 0.625 in (15.88 mm) 12,500 lb (5,700 kg) 125 lb (57 kg)
100 1.250 in (31.75 mm) 0.750 in (19.05 mm) 19,531 lb (8,859 kg) 195 lb (88 kg)
120 1.500 in (38.10 mm) 0.875 in (22.23 mm) 28,125 lb (12,757 kg) 281 lb (127 kg)
140 1.750 in (44.45 mm) 1.000 in (25.40 mm) 38,280 lb (17,360 kg) 383 lb (174 kg)
160 2.000 in (50.80 mm) 1.125 in (28.58 mm) 50,000 lb (23,000 kg) 500 lb (230 kg)
180 2.250 in (57.15 mm) 1.460 in (37.08 mm) 63,280 lb (28,700 kg) 633 lb (287 kg)
200 2.500 in (63.50 mm) 1.562 in (39.67 mm) 78,175 lb (35,460 kg) 781 lb (354 kg)
240 3.000 in (76.20 mm) 1.875 in (47.63 mm) 112,500 lb (51,000 kg) 1,000 lb (450 kg

For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):

Pitch (inches) Pitch expressed
in eighths
ANSI standard
chain number
Width (inches)
14 28 25 18
38 38 35 316
12 48 41 14
12 48 40 516
58 58 50 38
34 68 60 12
1 88 80 58

Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
 A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.

Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.

Roller chains made using ISO standard are sometimes called as isochains.

 

WHY CHOOSE US 

1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CHINAMFG Marketing Network
7. Efficient After-Sale Service System

 

The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.

We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CHINAMFG range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.

 

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Standard or Nonstandard: Standard
Application: Textile Machinery, Garment Machinery, Conveyer Equipment, Packaging Machinery, Electric Cars, Motorcycle, Food Machinery, Marine, Mining Equipment, Agricultural Machinery, Car, Textile Machinery, Garment Machinery, Conveyor
Surface Treatment: Polishing
Samples:
US$ 3/Meter
1 Meter(Min.Order)

|

Order Sample

Customization:
Available

|

Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost:

Estimated freight per unit.







about shipping cost and estimated delivery time.
Payment Method:







 

Initial Payment



Full Payment
Currency: US$
Return&refunds: You can apply for a refund up to 30 days after receipt of the products.

China wholesaler ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes

car parking chain

Are there any smart or automated car parking chain solutions that offer advanced features for improved efficiency?

Yes, there are smart and automated car parking chain solutions available that offer advanced features to enhance efficiency and user experience. These technologies leverage automation, data analytics, and connectivity to provide various benefits:

1. Automated Access Control: Smart parking chains are integrated with electronic access control systems, allowing for automatic detection of authorized vehicles and seamless entry without the need for manual intervention.

2. License Plate Recognition (LPR): Some automated systems use LPR technology to identify vehicles by their license plates, granting access to pre-registered vehicles without the need for physical credentials.

3. Mobile Apps: Smart parking chain solutions may have companion mobile apps that enable users to request access, pay for parking, or receive notifications about parking availability and status.

4. Reservation Systems: Advanced parking chains can be integrated with reservation systems, allowing users to reserve parking spaces in advance, ensuring a spot is available upon arrival.

5. Real-time Data: Smart parking chains can collect and provide real-time data on parking occupancy, traffic patterns, and usage, helping facility managers optimize parking space allocation and make informed decisions.

6. Remote Management: Automated parking chains can be remotely controlled, allowing operators to manage access and monitor the parking facility from a central location.

7. Intelligent Traffic Flow: Some smart systems can analyze traffic flow and optimize entry and exit points to reduce congestion and waiting times.

8. Payment Integration: Smart parking chains can be linked to payment systems, enabling automatic payment processing for users with valid access rights.

9. Integration with Other Technologies: Smart parking chains can be integrated with other technologies, such as parking guidance systems or smart sensors, to create a comprehensive and efficient parking management solution.

10. Enhanced Security: With automated access control and data monitoring, smart parking chain solutions offer enhanced security, reducing the risk of unauthorized access and enhancing user safety.

These advanced features make smart and automated car parking chains an attractive choice for modern parking facilities, offering improved efficiency, convenience, and user satisfaction.

car parking chain

What are the safety features of car parking chains to prevent accidents and injuries?

Car parking chains are designed with several safety features to prevent accidents and injuries. These features ensure that the chains operate safely and effectively, protecting both vehicles and users. Some common safety features include:

1. Reflective Elements: Many parking chains have reflective coatings or materials to enhance visibility, especially during low-light conditions. This makes the chains more noticeable to drivers and pedestrians, reducing the risk of collisions.

2. Smooth and Even Surface: Parking chains are manufactured with smooth and even surfaces to prevent any sharp edges or protrusions that could cause injuries or damage to vehicles.

3. Clear Signage: Proper signage is placed near the parking chains to inform users of their presence and how to operate them. This helps prevent confusion and misuse.

4. Low Friction: Chains are often lubricated to reduce friction and ensure smooth movement, minimizing the risk of accidents caused by chain jams or abrupt stops.

5. Emergency Access: Parking chains are designed with emergency access in mind. In manual systems, there are quick-release mechanisms to allow easy removal of the chain in emergency situations or to facilitate access for emergency vehicles.

6. Height and Clearance: Proper clearance is maintained to prevent chains from interfering with vehicles or causing damage during entry or exit.

7. Secure Mounting: Parking chains are securely mounted to prevent accidental detachment or falling, especially in retractable systems.

8. Load Capacity: For automatic systems, parking chains are designed to handle the weight of vehicles passing through, ensuring they can safely support the load.

9. Regular Maintenance: Regular inspections and maintenance help identify any safety issues and address them promptly, ensuring the chains remain safe for use.

10. Training and Education: Parking attendants and users should receive proper training on how to operate the parking chains safely and effectively.

By incorporating these safety features and promoting responsible use, car parking chains can effectively prevent accidents and injuries, providing a secure and controlled parking environment for all users.

car parking chain

How do automatic car parking chains work, and what are their advantages over manual systems?

Automatic car parking chains are an advanced version of traditional manual parking chains that offer more convenience and efficiency in controlling vehicle access. Here’s how they work and their advantages over manual systems:

1. Automated Operation: Automatic parking chains are integrated with electronic access control systems, such as keycard readers, RFID (Radio Frequency Identification) tags, or remote-controlled mechanisms. When an authorized vehicle approaches the entrance, the system automatically detects the vehicle’s credentials and raises the chain to allow entry.

2. Enhanced Security: With automated access control, there is a reduced risk of human error, which can be a vulnerability in manual systems. Only vehicles with valid credentials can enter, making it harder for unauthorized vehicles to gain access.

3. Time Efficiency: Automated car parking chains operate swiftly, minimizing waiting times for authorized users. This is particularly advantageous in high-traffic areas where manual control could cause congestion during peak hours.

4. Remote Management: Some automatic parking chains can be remotely controlled, allowing operators to manage access from a central location. This can be especially useful for large parking facilities or when physical attendance is not feasible.

5. Integration with Payment Systems: Automated chains can be connected to payment systems, enabling seamless access for users who have paid the required fees or have valid subscriptions.

6. Scalability: Automatic car parking chains can be easily integrated with other smart parking technologies, like ticketing systems or license plate recognition, to create a comprehensive and efficient parking management solution.

7. Reduced Labor Costs: As the system operates automatically, there is no need for manual attendance, leading to potential cost savings in labor.

8. Remote Monitoring: Some advanced automatic systems come with remote monitoring capabilities, allowing operators to track vehicle movement and access patterns in real-time.

Despite these advantages, automatic car parking chains may require higher upfront investment and ongoing maintenance costs compared to traditional manual systems. The choice between the two largely depends on the specific needs and budget constraints of the parking facility or garage.

China wholesaler ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes  China wholesaler ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes
editor by CX 2024-03-29

China Custom ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes

Product Description


ROLLER CHAIN

Roller chain or bush roller chain is the type of chain drive most commonly used for transmission of mechanical power on many kinds of domestic, industrial and agricultural machinery, including conveyors, wire- and tube-drawing machines, printing presses, cars, motorcycles, and bicycles. It consists of a series of short cylindrical rollers held together by side links. It is driven by a toothed wheel called a sprocket. It is a simple, reliable, and efficient means of power transmission.

LUBRICATION

Many driving chains (for example, in factory equipment, or driving a camshaft inside an internal combustion engine) operate in clean environments, and thus the wearing surfaces (that is, the pins and bushings) are safe from precipitation and airborne grit, many even in a sealed environment such as an oil bath. Some roller chains are designed to have o-rings built into the space between the outside link plate and the inside roller link plates. Chain manufacturers began to include this feature in 1971 after the application was invented by Joseph Montano while working for Whitney Chain of Hartford, Connecticut. O-rings were included as a way to improve lubrication to the links of power transmission chains, a service that is vitally important to extending their working life. These rubber fixtures form a barrier that holds factory applied lubricating grease inside the pin and bushing wear areas. Further, the rubber o-rings prevent dirt and other contaminants from entering inside the chain linkages, where such particles would otherwise cause significant wear.[citation needed]

There are also many chains that have to operate in dirty conditions, and for size or operational reasons cannot be sealed. Examples include chains on farm equipment, bicycles, and chain saws. These chains will necessarily have relatively high rates of wear, particularly when the operators are prepared to accept more friction, less efficiency, more noise and more frequent replacement as they neglect lubrication and adjustment.

Many oil-based lubricants attract dirt and other particles, eventually forming an CZPT paste that will compound wear on chains. This problem can be circumvented by use of a “dry” PTFE spray, which forms a solid film after application and repels both particles and moisture.

VARIANTS DESIGN

Layout of a roller chain: 1. Outer plate, 2. Inner plate, 3. Pin, 4. Bushing, 5. Roller
If the chain is not being used for a high wear application (for instance if it is just transmitting motion from a hand-operated lever to a control shaft on a machine, or a sliding door on an oven), then 1 of the simpler types of chain may still be used. Conversely, where extra strength but the smooth drive of a smaller pitch is required, the chain may be “siamesed”; instead of just 2 rows of plates on the outer sides of the chain, there may be 3 (“duplex”), 4 (“triplex”), or more rows of plates running parallel, with bushings and rollers between each adjacent pair, and the same number of rows of teeth running in parallel on the sprockets to match. Timing chains on automotive engines, for example, typically have multiple rows of plates called strands.

Roller chain is made in several sizes, the most common American National Standards Institute (ANSI) standards being 40, 50, 60, and 80. The first digit(s) indicate the pitch of the chain in eighths of an inch, with the last digit being 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. Thus, a chain with half-inch pitch would be a #40 while a #160 sprocket would have teeth spaced 2 inches apart, etc. Metric pitches are expressed in sixteenths of an inch; thus a metric #8 chain (08B-1) would be equivalent to an ANSI #40. Most roller chain is made from plain carbon or alloy steel, but stainless steel is used in food processing machinery or other places where lubrication is a problem, and nylon or brass are occasionally seen for the same reason.

Roller chain is ordinarily hooked up using a master link (also known as a connecting link), which typically has 1 pin held by a horseshoe clip rather than friction fit, allowing it to be inserted or removed with simple tools. Chain with a removable link or pin is also known as cottered chain, which allows the length of the chain to be adjusted. Half links (also known as offsets) are available and are used to increase the length of the chain by a single roller. Riveted roller chain has the master link (also known as a connecting link) “riveted” or mashed on the ends. These pins are made to be durable and are not removable.

USE

An example of 2 ‘ghost’ sprockets tensioning a triplex roller chain system
Roller chains are used in low- to mid-speed drives at around 600 to 800 feet per minute; however, at higher speeds, around 2,000 to 3,000 feet per minute, V-belts are normally used due to wear and noise issues.
A bicycle chain is a form of roller chain. Bicycle chains may have a master link, or may require a chain tool for removal and installation. A similar but larger and thus stronger chain is used on most motorcycles although it is sometimes replaced by either a toothed belt or a shaft drive, which offer lower noise level and fewer maintenance requirements.
The great majority of automobile engines use roller chains to drive the camshaft(s). Very high performance engines often use gear drive, and starting in the early 1960s toothed belts were used by some manufacturers.
Chains are also used in forklifts using hydraulic rams as a pulley to raise and lower the carriage; however, these chains are not considered roller chains, but are classified as lift or leaf chains.
Chainsaw cutting chains superficially resemble roller chains but are more closely related to leaf chains. They are driven by projecting drive links which also serve to locate the chain CZPT the bar.

Sea Harrier FA.2 ZA195 front (cold) vector thrust nozzle – the nozzle is rotated by a chain drive from an air motor
A perhaps unusual use of a pair of motorcycle chains is in the Harrier Jump Jet, where a chain drive from an air motor is used to rotate the movable engine nozzles, allowing them to be pointed downwards for hovering flight, or to the rear for normal CZPT flight, a system known as Thrust vectoring.

WEAR

 

The effect of wear on a roller chain is to increase the pitch (spacing of the links), causing the chain to grow longer. Note that this is due to wear at the pivoting pins and bushes, not from actual stretching of the metal (as does happen to some flexible steel components such as the hand-brake cable of a motor vehicle).

With modern chains it is unusual for a chain (other than that of a bicycle) to wear until it breaks, since a worn chain leads to the rapid onset of wear on the teeth of the sprockets, with ultimate failure being the loss of all the teeth on the sprocket. The sprockets (in particular the smaller of the two) suffer a grinding motion that puts a characteristic hook shape into the driven face of the teeth. (This effect is made worse by a chain improperly tensioned, but is unavoidable no matter what care is taken). The worn teeth (and chain) no longer provides smooth transmission of power and this may become evident from the noise, the vibration or (in car engines using a timing chain) the variation in ignition timing seen with a timing light. Both sprockets and chain should be replaced in these cases, since a new chain on worn sprockets will not last long. However, in less severe cases it may be possible to save the larger of the 2 sprockets, since it is always the smaller 1 that suffers the most wear. Only in very light-weight applications such as a bicycle, or in extreme cases of improper tension, will the chain normally jump off the sprockets.

The lengthening due to wear of a chain is calculated by the following formula:

M = the length of a number of links measured

S = the number of links measured

P = Pitch

In industry, it is usual to monitor the movement of the chain tensioner (whether manual or automatic) or the exact length of a drive chain (one rule of thumb is to replace a roller chain which has elongated 3% on an adjustable drive or 1.5% on a fixed-center drive). A simpler method, particularly suitable for the cycle or motorcycle user, is to attempt to pull the chain away from the larger of the 2 sprockets, whilst ensuring the chain is taut. Any significant movement (e.g. making it possible to see through a gap) probably indicates a chain worn up to and beyond the limit. Sprocket damage will result if the problem is ignored. Sprocket wear cancels this effect, and may mask chain wear.

CHAIN STRENGTH

The most common measure of roller chain’s strength is tensile strength. Tensile strength represents how much load a chain can withstand under a one-time load before breaking. Just as important as tensile strength is a chain’s fatigue strength. The critical factors in a chain’s fatigue strength is the quality of steel used to manufacture the chain, the heat treatment of the chain components, the quality of the pitch hole fabrication of the linkplates, and the type of shot plus the intensity of shot peen coverage on the linkplates. Other factors can include the thickness of the linkplates and the design (contour) of the linkplates. The rule of thumb for roller chain operating on a continuous drive is for the chain load to not exceed a mere 1/6 or 1/9 of the chain’s tensile strength, depending on the type of master links used (press-fit vs. slip-fit)[citation needed]. Roller chains operating on a continuous drive beyond these thresholds can and typically do fail prematurely via linkplate fatigue failure.

The standard minimum ultimate strength of the ANSI 29.1 steel chain is 12,500 x (pitch, in inches)2. X-ring and O-Ring chains greatly decrease wear by means of internal lubricants, increasing chain life. The internal lubrication is inserted by means of a vacuum when riveting the chain together.

CHAIN STHangZhouRDS

Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.

ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25

ASME/ANSI B29.1-2011 Roller Chain Standard Sizes
Size Pitch Maximum Roller Diameter Minimum Ultimate Tensile Strength Measuring Load
25 0.250 in (6.35 mm) 0.130 in (3.30 mm) 780 lb (350 kg) 18 lb (8.2 kg)
35 0.375 in (9.53 mm) 0.200 in (5.08 mm) 1,760 lb (800 kg) 18 lb (8.2 kg)
41 0.500 in (12.70 mm) 0.306 in (7.77 mm) 1,500 lb (680 kg) 18 lb (8.2 kg)
40 0.500 in (12.70 mm) 0.312 in (7.92 mm) 3,125 lb (1,417 kg) 31 lb (14 kg)
50 0.625 in (15.88 mm) 0.400 in (10.16 mm) 4,880 lb (2,210 kg) 49 lb (22 kg)
60 0.750 in (19.05 mm) 0.469 in (11.91 mm) 7,030 lb (3,190 kg) 70 lb (32 kg)
80 1.000 in (25.40 mm) 0.625 in (15.88 mm) 12,500 lb (5,700 kg) 125 lb (57 kg)
100 1.250 in (31.75 mm) 0.750 in (19.05 mm) 19,531 lb (8,859 kg) 195 lb (88 kg)
120 1.500 in (38.10 mm) 0.875 in (22.23 mm) 28,125 lb (12,757 kg) 281 lb (127 kg)
140 1.750 in (44.45 mm) 1.000 in (25.40 mm) 38,280 lb (17,360 kg) 383 lb (174 kg)
160 2.000 in (50.80 mm) 1.125 in (28.58 mm) 50,000 lb (23,000 kg) 500 lb (230 kg)
180 2.250 in (57.15 mm) 1.460 in (37.08 mm) 63,280 lb (28,700 kg) 633 lb (287 kg)
200 2.500 in (63.50 mm) 1.562 in (39.67 mm) 78,175 lb (35,460 kg) 781 lb (354 kg)
240 3.000 in (76.20 mm) 1.875 in (47.63 mm) 112,500 lb (51,000 kg) 1,000 lb (450 kg

For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):

Pitch (inches) Pitch expressed
in eighths
ANSI standard
chain number
Width (inches)
14 28 25 18
38 38 35 316
12 48 41 14
12 48 40 516
58 58 50 38
34 68 60 12
1 88 80 58

Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
 A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.

Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.

Roller chains made using ISO standard are sometimes called as isochains.

 

WHY CHOOSE US 

1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System

 

The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.

We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.

 

Shipping Cost:

Estimated freight per unit.



To be negotiated
Standard or Nonstandard: Standard
Application: Textile Machinery, Garment Machinery, Conveyer Equipment, Packaging Machinery, Electric Cars, Motorcycle, Food Machinery, Marine, Mining Equipment, Agricultural Machinery, Car, Textile Machinery, Garment Machinery, Conveyor
Surface Treatment: Polishing
Samples:
US$ 3/Meter
1 Meter(Min.Order)

|

Order Sample

Customization:
Available

|

Customized Request

China Custom ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes

car parking chain

How do I install a car parking chain correctly and securely to ensure its proper functioning?

Proper installation is crucial to ensure the car parking chain operates correctly and securely. Follow these steps for a successful installation:

1. Site Assessment:

– Conduct a thorough site assessment to determine the best location for the parking chain. Consider factors such as traffic flow, visibility, and clearance requirements.

2. Choose the Right Chain:

– Select a parking chain that suits the specific needs of your parking facility, considering factors such as traffic volume, vehicle types, and environmental conditions.

3. Measurements:

– Measure the width of the entrance or exit where the chain will be installed to ensure you select the appropriate length of the chain.

4. Anchor Points:

– Identify and prepare sturdy anchor points on either side of the entrance or exit to mount the parking chain. Ensure the anchors are securely attached to the ground or wall to withstand the force applied by the chain.

5. Chain Height:

– Position the parking chain at an appropriate height to allow vehicles to pass underneath without obstruction. Ensure there is sufficient clearance for all types of vehicles that will use the parking facility.

6. Installation:

– Install the parking chain according to the manufacturer’s instructions. Use appropriate tools and equipment to ensure a secure and stable installation.

7. Secure Attachment:

– Double-check that the chain is securely attached to the anchor points, and there is no excessive slack or sagging.

8. Signage:

– Install clear and visible signage to inform users about the presence of the parking chain and how to operate it.

9. Testing:

– Test the parking chain’s movement to ensure it raises and lowers smoothly without any obstructions or jams.

10. Maintenance:

– Develop a maintenance schedule and conduct regular inspections to ensure the parking chain remains in good working condition. Lubricate the chain and address any issues promptly.

By following these installation steps and providing regular maintenance, you can ensure the car parking chain functions correctly and securely, providing efficient access control and enhancing the overall safety and convenience of your parking facility.

car parking chain

Are there any regulations or guidelines regarding the installation and use of car parking chains in public and private parking lots?

Yes, the installation and use of car parking chains in public and private parking lots are subject to various regulations and guidelines to ensure safety, accessibility, and compliance with local laws. Here are some common considerations:

1. Building Codes and Zoning Regulations: Before installing parking chains, property owners or operators must comply with local building codes and zoning regulations that dictate the types of barriers and access control mechanisms allowed in specific areas.

2. Accessibility Requirements: Parking facilities, including those using parking chains, must comply with accessibility standards, ensuring that they are accessible to individuals with disabilities. This may involve providing designated accessible parking spaces and ensuring barrier-free access to the facility.

3. Height and Clearance: There are often regulations regarding the height of parking chains to prevent them from interfering with vehicles and causing damage. Adequate clearance must be maintained to ensure smooth entry and exit of vehicles.

4. Visibility and Signage: Proper signage should be displayed to inform users about the parking control system in place and to direct them on how to operate it. Adequate lighting should also be provided to ensure good visibility, especially during low-light conditions.

5. Safety Measures: Safety should be a priority when installing parking chains. This includes ensuring that the chain and its supports are securely anchored to prevent accidents or unauthorized removal.

6. Fire Safety Regulations: In certain areas, there may be specific fire safety regulations that dictate the use of specific materials or the inclusion of fire lanes for emergency vehicle access.

7. Permits and Approvals: Depending on the location and local regulations, obtaining permits and approvals from relevant authorities may be necessary before installing parking chains.

8. Compliance with Industry Standards: Manufacturers and installers of parking chains should ensure that their products meet industry standards for quality, durability, and safety.

It is essential for property owners, facility managers, and operators to familiarize themselves with the specific regulations and guidelines in their area and to work with reputable suppliers and installers to ensure compliance and the safe and effective use of car parking chains.

car parking chain

Can car parking chains be customized to fit specific parking space dimensions?

Yes, car parking chains can be customized to fit specific parking space dimensions. Manufacturers often offer customization options to cater to the unique requirements of different parking facilities. Here’s how parking chains can be customized:

1. Length Adjustment: Parking chains can be made to the exact length needed to span across the width of the entrance or exit of a specific parking space. This ensures a proper fit without any excess chain length that could lead to tangling or inconvenience.

2. Chain Link Size: The diameter and thickness of the individual chain links can be adjusted to match the desired strength and aesthetic preferences. Thicker links may be chosen for heavy-duty applications, while thinner links can be used for lighter traffic areas.

3. Color Options: Customization may extend to the color of the parking chain, with some manufacturers offering various color coatings or finishes to suit the parking facility’s design or branding requirements.

4. Retractable Mechanism: For parking areas that require flexible access control, parking chains can be integrated with retractable mechanisms, allowing them to be raised or lowered as needed.

5. Personalized Branding: In some cases, parking chains can be customized with logos or branding elements, particularly for commercial or corporate parking facilities.

6. Material and Coating: While most parking chains are made from steel for durability, specialized materials or coatings can be considered for unique environments, such as coastal areas with high corrosion potential.

Keep in mind that while customization offers tailored solutions, it may also affect the cost and lead time for manufacturing the parking chains. It’s essential to work with reputable manufacturers or suppliers who can provide guidance on the best customization options based on the specific needs of the parking facility.

China Custom ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes  China Custom ASME/ANSI B29.1-2011 240 Alloy/Carbon Steel/Stainless Steel Transmission Martin Car Parking/Sugar/Coal Machine Roller Chain Standard Sizes
editor by CX 2023-09-06